Portable DIY Mini Spot Welder Machine with LCD Display Automatic Touch Welding Mode for 18650 Battery 12V Car Battery
125
Direct purchase from the factory 
Malipo Salama Yanahakikishiwa
Zawadi ya Bure
Sera ya Usafirishaji
Sera ya KurudishaZawadi ya Bure
Karibu Roymall, tovuti yako ya kitaalamu ya kununua zawadi za hifadhi ya duka. Tunathamini na kushukuru msaada wako, na tunataka kuonyesha shukrani yetu kwa kuongeza kipengele cha msisimko wa ziada kwa ununuzi wako. Unaponunua nasi, sio tu utapata bidhaa za hali ya juu zinazoboresha maisha yako, lakini utapata pia zawadi ya bure ya kipekee kwa kila agizo lako. Tayari kuchunguza mkusanyiko wetu na kupata zawadi zako kamili? Chunguza uteuzi wetu wa bidhaa za hifadhi ya duka, weka agizo lako na subiri msisimko wa zawadi yako ya bure kufika pamoja na ununuzi wako.Sera ya Usafirishaji
Tutafanya kazi kwa bidii kukufikishia bidhaa baada ya kupokea maagizo yako na kuhakikisha zinafika salama. Maelezo ya uwasilishaji yatakuwemo kwenye barua pepe yako ya uthibitisho.Kwa hali ya kawaida, maagizo huchakatwa ndani ya siku 2. Katika hali maalum, yanaweza kucheleweshwa kama ifuatavyo: Unapoagiza Jumamosi, Jumapili au siku za likizo, itacheleweshwa kwa siku 2.Kwa kawaida, inahitaji siku 5-7 za kazi (Jumatatu hadi Ijumaa) bila kuathiriwa na ucheleweshaji wa ndege au mazingira mengine.Kwa sababu huduma yetu ya usafirishaji ni kimataifa, muda wa uwasilishaji utategemea eneo lako, kwa hivyo inaweza kuchukua muda na tafadhali subiri kwa subira ikiwa uko katika wilaya au nchi za mbali.1. Sera ya Kurudisha na Kubadilisha
Tunakubali tu bidhaa zilizonunuliwa kutoka roymall.com. Ikiwa unanunua kutoka kwa wasambazaji wetu wa ndani au wauzaji wengine, huwezi kuzirudisha kwetu. Bidhaa za mauzo ya mwisho au zawadi za bure hazikubaliki kwa kurudisha.Ili kuwa na haki ya kurudisha, bidhaa yako lazima isitumike na iwe katika hali ileile uliyoipeleka. Pia lazima iwe kwenye pakiti ya asili.Baada ya kupokea maagizo ya kurudisha kutoka kwetu, tafadhali pakiti bidhaa zako zilizorudishwa na kuacha kifurushi chako kwenye ofisi ya posta ya ndani au mtoa huduma mwingine wa usafirishaji.Tutachakata bidhaa yako ya kurudisha au kubadilisha ndani ya siku 3-5 za kazi baada ya kuipokea. Rudi pesa itachakatwa na kuwekwa kiotomatiki kwenye njia yako ya awali ya malipo.Hakuna kurudisha au kubadilisha kunaweza kukubaliwa ikiwa bidhaa ilitengenezwa kwa maagizo maalum, ikiwa ni pamoja na saizi maalum, rangi maalum au uchapishaji maalum.Ikiwa unahitaji msaada zaidi, tafadhali wasiliana nasi. service@roymall.com au Whatsapp: +8619359849471
2. Sera ya Kurudisha Pesa
Utapata rudi pesa kamili au stoo 100% ya stoo baada ya kupokea na kukagua kifurushi kilichorudishwa. Rudi pesa itachakatwa kiotomatiki kwenye njia yako ya awali ya malipo.Tafadhali kumbuka kuwa gharama za usafirishaji na ushuru wowote au ada hazirudishiwi. Gharama za ziada za usafirishaji hazirudishiwi mara tu kifurushi kimetumwa. Wewe ndiye mwenye jukumu la kulipa ada hizi na hatuwezi kuziacha au kuzirudisha, hata kama agizo litarudishwa kwetu.Mara tu tutakapopokea na kuthibitisha bidhaa yako iliyorudishwa, tutakutumia barua pepe kukujulisha kuwa tumepokea bidhaa yako. Pia tutakujulisha kuhusu uthibitisho au kukataliwa kwa rudi pesa yako.Ikiwa una shida yoyote kuhusu mchakato wa kurudisha pesa, tafadhali wasiliana nasi. service@roymall.com au Whatsapp: +8619359849471
Features:
1. Wide selection of welding power supply: lithium battery power supply or 12V car battery.
2. The controller is controlled by a single chip microcomputer, and the output pulse is accurate to ensure the welding quality.
3. With LCD display screen, can display welding parameters.
4. The welding pen and the input line are connected by U-shaped cold-pressed terminals, which is convenient for disassembly and replacement.
5. Using automatic touch welding mode, while retaining the manual trigger interface, you can choose according to your own use.
6. The power board uses 2 Gusi copper to increase the overcurrent capacity.
7. Using 5*300A MOS tubes, non-disassembled MOS tubes.
8. The MOS tube driver adopts the imported special chip driver. The fastest MOS tube can be hit with 20nS. The switch is fast to prevent the explosion of the tube and the non-triode push-pull drive.
9. The MOS drive design adds a transient diode to protect the MOS and prevent the explosion of the tube.
10. 10AWG multi-filament flexible wire is used for the welding pen line and the input line to increase the overcurrent capacity.
11.The controller is mainly for welding nickel-plated steel strips from 0.1mm to 0.15mm.
12. A 25V10000uF high-frequency low-resistance capacitor is added to the power input for energy compensation, which increases welding stability.
Instructions for Use:
1: Power Connection
The controller comes with a 20cm long 10AWG input wire. One end has been crimped with a U-shaped terminal, and the other end has not been processed. Connect the crimped U-shaped terminal to the control power input terminal, and the other end is processed according to its own power supply. Do not connect the negative electrode wrong.
2: Switch on and off
There is a power switch under the control board. After pressing, wait for 3 seconds. After the buzzer drops, the LCD lights up and the boot is complete. Press the power switch again to shut down.
3: Screen description and parameter adjustment.
WELD ENERGY: 01-99 (adjustable by up and down keys)
INPUT: Display input power voltage
WELD WAY: Manual / Auto (Adjust via the "square label" button.)
4: Welding
Keep the welding pin clean. If the welding pin is polished into a round head, the welding effect can be improved. There are manual and automatic methods.
Specification:
Material: Metal
Input line length: app.20cm/7.87in
Length of welding pen: app.30cm/11.81in
Color: Red+Blue+Black
Battery: 18650 lithium battery(not included)
Quantity: 1Set
Note:
The controller comes with a 20cm long 10AWG input cable. One end has been crimped with a U-shaped terminal and the other has not been processed. Connect the crimped U-shaped terminal to the control power input terminal, and the other end is processed according to its own power supply.
There is an ignition switch underneath the control board. After pressing, wait 3 seconds. After the bell rings, the LCD screen lights up and the boot is complete. Press the power switch again to close it.
Please allow 1-2cm size errors due to manual measurement.
Item color displayed in photos may be showing slightly different on your computer monitor since monitors are not calibrated same.
Package Included:
1 x Controller
2 x Welding Pen
2Pcs x Power Input Line (Red and Blue)
1 Pair x U-shaped cold-pressed terminal (used to connect to input power)
1 x Black Plug (When you choose manual mode, It need an external trigger switch to connector black plug.)
